 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Series AMSR-78-NZ Up to 7.5Watt | DC-DC Converter FEATURES: * * * * RoHS Compliant 3 Pin SIP Package Non-Isolated Low ripple and noise * * * * Operating temperature -40C to +85C Very high efficiency up to 96% Pin compatible to multiple manufacturers Regulated Outputs Models Single output Model AMSR-783.3-NZ AMSR-7805-NZ AMSR-786.5-NZ AMSR-7809-NZ AMSR-7812-NZ AMSR-7815-NZ Input Voltage (V) 4.75-28 6.5-32 8-32 11-32 15-32 18-32 Output Voltage (V) 3.3 5 6.5 9 12 15 Output Current max (mA) 500 500 500 500 500 500 Efficiency Vin Max (%) 90 93 94 95 95 96 Efficiency Vin Min (%) 80 84 87 91 92 93 Input Specifications Parameters Voltage range Filter Quiescent current Short circuit consumption Conditions Vin=(LL-HL) at 0% load Typical See the table above Capacitor Maximum 7 0.8 Units VDC mA W Output Specifications Parameters Voltage accuracy Short Circuit protection Short circuit restart Output current limit Thermal shutdown Dynamic load stability Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Conditions 100% load Typical 3 Continuous Auto recovery Maximum Units % 2 Internal IC junction 10-100% load Vin=(LL-HL) at full load 10-100% load -40C to +85C ambient 20MHz Bandwidth 150 100 0.4 0.6 0.02 35 A C mV % % %/oC mV p-p o General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 330 KHz o Operating temperature With derating above 71 oC -40 to +85 C o Storage temperature -55 to +125 C o Max Case temperature 100 C Cooling Free air convection Humidity 95 % Case material Non-conductive black plastic (UL94V-0 rated) Weight 2 g Dimensions (L x W x H) 0.45 x 0.30 x 0.40 inches 11.50 x 7.60 x 10.20 mm MTBF > 2 000 000 hrs (MIL-HDBK-217F, Ground Benign, t=+25 oC) o Soldering Temperature 1.5 mm from case for 10 sec 300 C NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. www.aimtec.com F 051e R6.B Tel: +1 514 620 2722 1 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR-78-NZ Up to 7.5Watt | DC-DC Converter Pin Out Specifications Pin 1 2 3 Dimensions 11.50 (0.45) PRINTED FACE Single +V Input Ground +V Output 9.70 (0.38) 7.55 (0.30) 0.50 (0.02) 0.50 (0.02) 7.55 (0.30) 2.10 (0.08) 0.50 (0.02) Dimensions are in mm (inch) Pin Tolerance: 0.16 mm (0,004 inch) Case Tolerance: 0.25 mm (0.01 inch) Derating www.aimtec.com F 051e R6.B Output Power (%) Tel: +1 514 620 2722 2 of 3 0.30 (0.01) 4.00 (0.16) 2.54 (0.1) Toll free: + 1 888 9 AIMTEC (924 6832) North America only 10.20 (0.40) Series AMSR-78-NZ Up to 7.5Watt | DC-DC Converter Standard Application Circuit Vin 1 C1 10F AMSR 78XX- NZ - 3 C2 100F Vout 2 GND GND C1: A low ESR capacitor is required to keep the noise of the converter to a minimum. Ceramic capacitors are recommended, but tantalum or electrolytic may be used. Typical value is 10F / 50V. C2: Installation of C2 is recommended but optional. Typical recommended value is 100F / 25V electrolytic. NOTE: This part is not designed for parallel operation NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com F 051e R6.B Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only |
Price & Availability of AMSR-7812-NZ
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |